10 Things Everyone Has To Say About Repair Car Keys Repair Car Keys

How to Repair Car Keys

Car keys may seem tiny and insignificant, but they are essential to the operation of your vehicle. Replacing a traditional key or a transponder key that is modern could cost as much as $200.

However, there are ways to repair your car keys at home for a fraction of the cost. This article will discuss the most frequent car keys problems and their DIY fixes.

Dead Key Fob Batteries

The remote key fobs for keys that come with cars make it easier than ever before to open the trunk, doors, and the tailgate. The battery of this device is prone to dying. There are a few strategies you can use to resolve this issue quickly.

First, check if the car is still in ignition mode. If it is, the battery on the key fob could be drained instead of dead. To test this, press the button on the fob against the ignition button on the vehicle. If this works, then the battery is probably in good condition and will only need to be replaced.

To replace the fob's battery, begin by prying the case off using an instrument like a screwdriver, or watch-type tool. Don't apply too much force as this may cause the fob's case split. If the fob isn't opening try prying the tool more than once around the outside of case.

Once the fob is opened then remove the mechanical key and open the electronic portion of the car. Then, insert the battery replacement and snap the shell back together. If the key fob doesn't work after this procedure, there could be a larger problem with the remote start system that requires a professional diagnostic. If this is the case, a trusted mechanic should be able to assist you. If you need help with your car and you need help, you can call roadside assistance.

Broken Key Ring

There are a few things to do in the event that your key fob won't work because the ring has been broken. Check to see if you can locate the broken part inside the ignition. If it is, you should remove it without damaging the door lock or ignition lock. If you have trouble getting it out, contact a locksmith for assistance. They have the right tools to safely remove a damaged or broken key from the ignition.

A damaged car key could be caused by corrosion on the plastic frame or circuit board. You can clean the circuit board by using a cotton swab with ruby alcohol. This will eliminate the corrosion and stop damage to the contact pads.

If your key won't start because the ring is broken it, you might be able fix it with a strong wire or nail to plug the hole. Superglue can be used to fix a broken key ring. First, clean the broken ring with a damp cloth and then apply a small amount superglue to each end of the nail or wire. Allow the pieces to dry, and then press them in place. These DIY solutions might seem appealing, however they are only temporary solutions. For long-term repairs, it's recommended to work with a professional locksmith. They have the tools and expertise to repair a damaged car key quickly and effectively. They can even replace the battery on your key fob and modify it if necessary.

Broken Key Blade

Some key blades can break because of a lot wear and tear. If this happens, it's probably time to get a new key. This problem isn't nearly as serious as you think at first. The primary issue is that the blade snapped off the case.

Spraying lubricant into the keyhole is a method to fix it. You can then make use of pliers or tweezers grab the broken end of the key and pull it. If the key is magnetic, you could also use a magnet to assist in pulling it out. Use a magnet as a aid to you remove the key, but be cautious to not damage the lock tumbler.

If you're unable to take the broken piece of key, contact an expert locksmith immediately. They have the right tools to safely remove keys without causing further damage.

key fob repair  can also apply super glue to fix a snapped key. Apply a small amount of the glue to the edges and press them in. Make sure the glue has dried before inserting the key into the lock. This method isn't reliable and you may have to repeat the process a few times before it is successful. Super glue may not hold the key together. Therefore, this is more of a temporary measure than a permanent solution.

Broken Plastic Loop

If the plastic loop is damaged, it can make the key useless. Luckily, this is a fairly simple fix. As a replacement alternative, you can use an extremely thick wire or a finishing nail. For each end of the wire or nail you need to drill two holes into the plastic loop. Cut the nail or wire to key width and put a drop of superglue in each hole. Put the nail or wire into the holes until it closes them and allow it to dry.

Another option is to get an alternative shell from a locksmith that sells them. They can transfer the programmable part of your key into the new shell, and then cut an entirely new blade at a fraction of the cost.

It's not the ideal solution, but it can get you back on the road in case your key split in half. It's not easy to fix when the key blade is inside the ignition, however. You can try using hair clips or needle extractor tool to remove the damaged piece of the ignition, however this can be risky if not careful. Call a locksmith with special tools to safely remove broken keys from ignitions. You can also have a new key that is made using the correct cuts to fit the ignition of your vehicle.

Broken Master Key

If a key breaks inside the lock, you'll need to find it before it's completely destroyed. There are several methods you can employ, such as using lubricants, tools, needle nose pliers and tweezers to take a small piece of the damaged key and remove it.

To start, spray the inside of your lock with a lubricant such as WD-40 or graphite powder. You can also use hacksaw blades, which involves sliding the blade across the face of a damaged key and grabbing onto some of its 'teeth.' If you are successful then you should be able to cut the damaged key.

Many hardware stores offer the spiral key extraction tool. It is a thin, flexible bar with spiral threads, that can be inserted into the keyway and then bent to dig into the broken section of the key. Once it is firmly anchored to the serrations you can twist the bar into a circle and then pull it against the damaged section of the key.

It's worth trying to remove a master key that's broken prior to calling a professional locksmith. If you're unable to pull a piece out, you need to call in the big guns and get a locksmith to cut you a brand new key and reprogram it to your car's transponder.